Normally, a Windows 10 computer starts up as soon as you press the power button. In most cases, booting a Windows PC is not a problem. Sometimes the boot process does not start even after pressing the power button several times. It’s rare for Windows 10 to fail to boot, but some system or hardware errors can cause this problem.
For most users, it is difficult to solve this problem because it is not accompanied by an error message on the screen and it becomes difficult to connect. However, the problem can be solved by using the Windows recovery environment (WinRE) and safe mode.
22 Windows 10 does not resolve boot issues
Sometimes you only see a black screen when you log in. The black screen problem is different from the boot problem. If you get an error message on the black screen, at least you can connect for a while. However, if Windows 10 doesn’t boot at all, it means you won’t even see the manufacturer’s logo or the login screen after pressing the power button.
You can easily fix the boot problem on your Windows 10 PC with a little bit of technical knowledge and the solutions listed below.
1. Disconnect all external devices and USB drives.
The connected USB device and external devices, such as. B. an external storage device or headphones, may interfere with the boot process. To restart the computer, disconnect all external devices and press the power button. Many users quickly get rid of their charging problems with this simple solution.
2. To safe mode
Safe mode starts by restricting drivers and software. When Windows 10 fails to boot due to driver and software issues, safe mode can solve the problem to some extent. You need to go to safe mode through the Windows recovery environment.
After going to safe mode, you can perform some of the following repairs in safe mode. However, if you cannot run Windows 10 in safe mode, the only way to resolve the issue is to use WinRE.
3. Delete last added devices
If you have recently installed new hardware on your computer, you can remove it and see if you can connect. The device may be damaged or incompatible with your PC. If a PC repair shop has the latest equipment, the replacement can be done there.
Sometimes equipment can fail after working properly for a few days. So be sure to check newly added material and correct any problems.
4. Check the charging cable and battery.
This only applies to laptops, as your laptop will not start without a battery. If your laptop’s battery is low and the power cord can’t charge it, Windows 10 won’t start up. You can try using a different charging cable, but make sure it is compatible with your laptop, otherwise it might damage your computer’s hardware components.
If the power from the outlet is insufficient, try switching to a different outlet. Make sure you check everything about your laptop’s battery, as this could be the main reason why Windows 10 won’t boot.
5. Performing a DISM and CFS scan
You can run scans to repair damaged and corrupted system files. Your Windows 10 will not start up if your system files have problems. The System File Checker (SFC) and Deployment Image Servicing and Management (DISM) utilities can help troubleshoot system file issues.
To start the scan, use WinRE to enter safe mode, then type cmd from the Start menu. Click Run as Administrator after selecting the command line in the search results.
alt=Enter the command line as administrator to fix Windows 10 does not start data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/What-To-Do-When-Windows-10-Wont-Boot.png />Enter the command line as administrator
In the terminal window, type the command sfc /scannow and press Enter.
alt= Running the SFC command to fix Windows 10 that won’t start data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379857_336_What-To-Do-When-Windows-10-Wont-Boot.png /> Running the SFC command
It may take a while for the command to complete; wait until it does. You can run the following command on the same line of the terminal.
Image removal/cleaning/restoration
alt=execute DISM command data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379857_232_What-To-Do-When-Windows-10-Wont-Boot.png />execute DISM command
After running both commands, check whether the boot error is fixed or not.
6. Performing startup recovery
You can perform boot recovery on a Windows 10 PC to resolve boot issues. To perform a boot-time recovery, you must start the Windows Recovery Environment.
Step one: Press the power button to turn on the computer, and then cancel the startup process by pressing the power button again to turn off the computer. Repeat this process three times or until you see the Prepare Automatic Repair section.
You can also use the installation disk to enter WinRE.
Step two: On the Auto Repair screen, click the Advanced Options button.
Step three: Now select Troubleshooting ➜ Advanced Options and click the Restore Startup button.
alt=Click startup repair data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379858_671_What-To-Do-When-Windows-10-Wont-Boot.png />Click startup repair
You can then follow the on-screen wizard to complete the repair.
7. Scan for viruses and malware
Malware and viruses can prevent your PC from starting up properly. If Windows 10 does not start even after the boot repair, you should check your computer for viruses.
Since the computer won’t boot, you need to run a malware scanner from a USB stick, CD or DVD. You can contact support about a bootable USB drive if you already have antivirus software on your computer.
If your antivirus software does not offer this option, you can search online for other ways to perform a scan.
8. Reset drive letter
If no letter is assigned to the system drive, Windows 10 will not boot. To solve this problem, assign a letter to the system drive.
Open the Windows recovery environment by pausing the boot process 3 times, then go to Diagnostics ➜ Advanced Settings ➜ Command Prompt.
In the command line window, type disk partition and press the Enter key on your keyboard.
After entering the hard disk partition, run the Volume List command. Here you can check the unallocated system disk and assign a letter to it.
If the unallocated drive is volume 0, run the command to select volume 0. The volume number can be changed accordingly.
alt=Execute command in diskpart to resolve Windows 10 does not start data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379859_287_What-To-Do-When-Windows-10-Wont-Boot.png />execute command in diskpart
Once the volume is selected, assign a letter to it using the assign letter=F command. You can change the letter as you like. You can enter an Exit command and press Enter to exit the disk space.
Now try restarting the computer and see if it starts up without any problems.
9. Monitor control
Sometimes the problem is with the screen, not the boot process. Your desktop or laptop computer may boot correctly, but it may not appear on your screen. Make sure the monitor is properly connected to the processor and power supply.
Also check that the input is set correctly and that the brightness is not reduced so much that the screen is blank. For laptops, check the screen for damage.
You can connect another monitor to see if you can see anything on the screen. If you don’t have another monitor, try connecting the processor to the TV and see if it works properly.
10. Disable fast boot in BIOS
Fast preloading of drivers to reduce loading time. Sometimes this can be one of the reasons why Windows 10 won’t boot. You need to go into the BIOS and disable fast startup.
The way you enter the BIOS may vary from manufacturer to manufacturer and from model to model. To know how to enter the BIOS correctly, refer to the manual that came with your computer.
After you open the BIOS, check the Quick Boot box. In most cases this is located under the Advanced option. If you can’t find it in the Advanced section, check your PC’s manual or the manufacturer’s website. You may not find the Quick Start option on some models released before 2013.
When you find the Quick Start setting, disable it and save your changes.
11. Uninstalling the latest Windows update
If you have recently updated your Windows operating system and are now experiencing boot problems, you need to remove the Windows update. Windows 10 will not start if the latest update is not compatible with your PC or contains errors. In both cases, the only solution is to remove the latest update.
From the Start menu, go to the Troubleshooting ➜ Advanced Options page. Then you need to click on the Remove Updates button.
alt= Click Remove Updates data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379860_147_What-To-Do-When-Windows-10-Wont-Boot.png /> Click Remove Updates
Follow the on-screen instructions to remove the latest update. You can then try restarting the computer to see if the boot process completes.
12. Check the connections to the main board
You can check the connection to the motherboard by opening your laptop or CPU. If any of the connections are loose or improper, they must be repaired.
Message: If your computer is under warranty, we recommend that you do not open the computer yourself. Otherwise, your computer will lose its warranty.
After opening the computer, check especially the RAM memory, operating system hard drive and PCI-E cards. Also check the motherboard for broken circuits.
13. Check defective plate
If there are bad sectors or errors on the system hard disk, Windows cannot be started. You can run the chkdsk command to scan and repair damaged sectors on the hard drive.
Open the command line as described in the solutions above and run the following command.
Chkdsk C: /f /x /r
alt=Perform the chkdsk command to restore Windows 10 will not boot data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379860_232_What-To-Do-When-Windows-10-Wont-Boot.png />Perform the chkdsk command
Here, C is the system drive. If the system drive is assigned a different letter, C can be replaced by that letter.
Windows restarts your computer and checks for problems. Save this; Windows 10 will boot normally.
14. Testing the hard disk on another PC
You can try testing the hard drive on another computer to see if there are any failures. For this purpose, the hard drive must be removed from the damaged PC and connected to another system.
This may require some special knowledge, otherwise the hard drive may be damaged. After you put it on another computer, you need to check whether your computer can boot up properly or not.
15. Check if your PC has completed the boot process (POST).
If the POST process is incomplete, the computer cannot transfer control to the operating system. You must confirm that your system has completed the power-on self-test (POST). To check this, see if the POST field at the bottom of the screen is completely filled.
16. Execution of loading orders
The bootrec command can fix boot-related problems in Windows 10. To correct the errors in the boot record and master boot record, run the following commands in the command line terminal.
Open a command line terminal with the Windows recovery environment and run the following commands in order.
BOOTREC /FIXMBR
BOOTREC /FIXBOOT
BOOTREC /RebuildBcd
After running each command, you will see Operation Successfully Completed. Some Windows users may not be able to run the BOOTREC /RebuildBcd command. In this case, the following commands must be executed.
bcdedit /export C:BCD_Backup
c :
Starting the CD
Attribute bcd -s -h -r
run c:bootbcd bcd.old
BOOTREC /RebuildBcd
If the system drive is not C, replace it with another letter in the command. Use the above commands to save the data storage of the boot configuration, then run the BOOTREC /RebuildBcd command.
17. Skip the boot loader in Windows 10
You may experience problems during a clean install of Windows 10. The new version of the bootloader may interfere with the existing bootloader, making it harder to start Windows 10. To solve this problem, you need to run a single command.
Open a command prompt and type the following command. Press the Enter key to execute it.
bcdedit /set {default} bootmenupolicy legacy
This will resolve your issues with opening safe mode and booting your Windows 10 PC.
18. Performing a clean start loader
If certain third-party applications or services interfere with the startup process, temporarily disable them. A clean shoe can help.
You need to start Windows 10 in safe mode and then type msconfig in the start menu. Open the system configuration from the search results.
Now select the Services tab and check the Hide all Microsoft services box. Click Disable All to disable all third-party services.
alt=Disable all third-party services so Windows 10 does not start data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379861_256_What-To-Do-When-Windows-10-Wont-Boot.png />Disable all third-party services.
Next, click on the Start tab and then on Open Task Manager. Click OK in the System Configuration window to close it.
alt=Open Task Manager data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379862_71_What-To-Do-When-Windows-10-Wont-Boot.png />Open Task Manager
Make sure you are in the Startup tab of the Task Manager window and right-click on the applications that do not need to be started. Choose Disable from the context menu.
alt=Open Startup Programs data-ezsrc=http://server.digimetriq.com/wp-content/uploads/2021/04/1619379863_986_What-To-Do-When-Windows-10-Wont-Boot.png />Open Startup Programs
Close the Task Manager window and restart the PC in normal, unprotected mode. Check whether Windows starts up normally or not.
If this is the case, services and applications should be activated one by one to find the culprit.
19. BIOS Update
Sometimes an outdated BIOS can cause problems when booting Windows 10. You can update your BIOS by visiting the manufacturer’s website to get the latest version for your PC. Updating the BIOS is a time-consuming process that requires technical knowledge.
However, you need to be careful when doing this because BIOS updates are difficult and if something goes wrong, your PC will crash. We therefore recommend that you seek expert assistance when carrying out this operation for the first time.
20. System recovery
You can restore your computer until everything is working properly again with a system restore point. Your personal files and data will not be deleted; only applications installed after the restore point was created will be removed from your system.
To perform a system restore, log into the Windows recovery environment and go to Troubleshooting ➜ Advanced Options. Click on System Restore to start the process.
21. Resetting Windows 10
If system restore did not work or there is no restore point, you can reset Windows 10. You can keep your files and data during the reset, so no need to worry about that.
Reset reinstalls the Windows operating system without the installation disk. This is a simple process that can help you solve many problems. Unless you have important data on your computer, we recommend that you do not back up your personal files and data during a reboot.
22. Clean installation of Windows 10
The last option to fix Windows 10 boot problems is to clean up your operating system installation. If Windows 10 does not boot after applying all the above solutions, you need to clean up your Windows 10 installation.
You can use the Windows Media Builder to create USB or DVD installation media and start a clean installation. After installation, the computer starts up without any errors or problems.
Supplement
Our work and games can grind to a halt if Windows 10 doesn’t start as soon as you press the power button. You will only see black screens and not the boot process. This can have several causes, for example B. Conflicts with external devices, battery problems, boot record errors and some unknown problems.
You may not know the real reason why Windows 10 won’t start because the problem doesn’t come with an error message, making it difficult to find solutions. However, the long list of solutions above can help you restart Windows 10 without any problems.
frequently asked questions
What should I do if my computer won’t start up after I turn it on?
What-what-what-what-what-what…
Cannot start Win 10 in safe mode?
Windows_10 implementation
How to solve Windows 10 freezing on the start screen?
The hard drive partition wins…
Related Tags:
Feedback,windows 10 won’t boot black screenwindows 10 won’t start upwindows 10 startup repair not workingwindows 10 won’t boot after update 2020windows 10 won’t boot past logowindows 10 won’t boot spinning circle,People also search for,Privacy settings,How Search works,windows 10 won’t boot black screen,windows 10 won’t start up,windows 10 startup repair not working,windows 10 won’t boot after update 2020,windows 10 won’t boot past logo,windows 10 won’t boot spinning circle,windows 10 startup repair command prompt,windows 10 not booting
